Luke7019 vs "AsaPerformance EVO"

BoostAlmighty wrote:

drastic is just crying because his car is slow

lol and you are?

here's a new(er) updated vid of my car doing 60 rolls w/ 26" slicks aired WAY down, on moderate boost, and 14* timing. reason timing was so low was because bad race gas. usually sees 20-24*. still roasts the slicks to 115mph on low timing.

[You must be registered and logged in to see this link.]

Phantom SRT4 wrote:

Drastic. wrote:

BoostAlmighty wrote:

Drastic. wrote:

Phantom SRT4 wrote:

are those low compression pistons?

looked like wisecos or CP's to me due to the design.


i have ragetek's low compression pistons.


DONT buy em if theyre on your list of consideration.

why not?

too low of a compression. IDGAF what shea (ex-employee at ragetek) says to defend them. the car is sluggish driving around town, and idles like shit w/ big cams. the low compression also contributed to worse mpg.

my motor is VERY stout and i can do 8k wot shifts and 600+ all day w/o it flinching...just i'll be replacing the 7.0's for some 9.0 pistons.

there is ZERO reason for low compression. find me companies that build motors for other types of cars w/ less than 8.5:1, and id be surprised.

unless you run straight up pump gas w/ zero meth and never run race gas, 7.0's shouldnt even be an option imo...

get higher compression, run good octane, keep an eye on timing, and reap the benefits of more spool, better mpg, better driveability off boost, and more power per lb of boost than the 7.0s.

i bought into a gimic and sadly i wish i didnt.
give me a good enough offer, and ill pull my pistons out and sell em 3600 miles on em.

I dont know of any other 6.9-7.2 compression SRT4s with those issues...

what do you mean? how many srts do you know w/ the 7.2s?

it's not a matter of opinion. a higher compression WILL increase mpg, increase throttle response, increase spool, all the while making more power doing it.

i went from stock, to 8.5:1 pistons, to 7.2:1 pistons..and noticed the differences between each time doing it.

Drastic. wrote:

Phantom SRT4 wrote:

Drastic. wrote:

BoostAlmighty wrote:

Drastic. wrote:

Phantom SRT4 wrote:

are those low compression pistons?

looked like wisecos or CP's to me due to the design.


i have ragetek's low compression pistons.


DONT buy em if theyre on your list of consideration.

why not?

too low of a compression. IDGAF what shea (ex-employee at ragetek) says to defend them. the car is sluggish driving around town, and idles like shit w/ big cams. the low compression also contributed to worse mpg.

my motor is VERY stout and i can do 8k wot shifts and 600+ all day w/o it flinching...just i'll be replacing the 7.0's for some 9.0 pistons.

there is ZERO reason for low compression. find me companies that build motors for other types of cars w/ less than 8.5:1, and id be surprised.

unless you run straight up pump gas w/ zero meth and never run race gas, 7.0's shouldnt even be an option imo...

get higher compression, run good octane, keep an eye on timing, and reap the benefits of more spool, better mpg, better driveability off boost, and more power per lb of boost than the 7.0s.

i bought into a gimic and sadly i wish i didnt.
give me a good enough offer, and ill pull my pistons out and sell em 3600 miles on em.

I dont know of any other 6.9-7.2 compression SRT4s with those issues...

what do you mean? how many srts do you know w/ the 7.2s?

it's not a matter of opinion. a higher compression WILL increase mpg, increase throttle response, increase spool, all the while making more power doing it.

i went from stock, to 8.5:1 pistons, to 7.2:1 pistons..and noticed the differences between each time doing it.

should just get a honda!

gsr interga wrote:

Drastic. wrote:

Phantom SRT4 wrote:

Drastic. wrote:

BoostAlmighty wrote:

Drastic. wrote:

Phantom SRT4 wrote:

are those low compression pistons?

looked like wisecos or CP's to me due to the design.


i have ragetek's low compression pistons.


DONT buy em if theyre on your list of consideration.

why not?

too low of a compression. IDGAF what shea (ex-employee at ragetek) says to defend them. the car is sluggish driving around town, and idles like shit w/ big cams. the low compression also contributed to worse mpg.

my motor is VERY stout and i can do 8k wot shifts and 600+ all day w/o it flinching...just i'll be replacing the 7.0's for some 9.0 pistons.

there is ZERO reason for low compression. find me companies that build motors for other types of cars w/ less than 8.5:1, and id be surprised.

unless you run straight up pump gas w/ zero meth and never run race gas, 7.0's shouldnt even be an option imo...

get higher compression, run good octane, keep an eye on timing, and reap the benefits of more spool, better mpg, better driveability off boost, and more power per lb of boost than the 7.0s.

i bought into a gimic and sadly i wish i didnt.
give me a good enough offer, and ill pull my pistons out and sell em 3600 miles on em.

I dont know of any other 6.9-7.2 compression SRT4s with those issues...

what do you mean? how many srts do you know w/ the 7.2s?

it's not a matter of opinion. a higher compression WILL increase mpg, increase throttle response, increase spool, all the while making more power doing it.

i went from stock, to 8.5:1 pistons, to 7.2:1 pistons..and noticed the differences between each time doing it.

should just get a honda!

i semi wish! i love my neon. but its hard to beat a built honda in a shell that would weigh in at 21-2200lb and put down big #s.. lol
my next project will be either EG hatch w/ a b18 w/ a billet 4294r, or an Evo w/ a billet 6765 unless i go turbo v8.
I want something that i can do digs all day w/, so evo or boosted v8 is looking to be the next choice..

Drastic im alrdy ahead of u i jus got a eg hatch b18b with gsr head for ls vtec lil somethin on the side

Papa-Smerf69 wrote:

Drastic im alrdy ahead of u i jus got a eg hatch b18b with gsr head for ls vtec lil somethin on the side

damn! nice man. what trans you mating to it? guna be all motor, or guna boost it?

ill keep a lookout for progress on it in ur posts. i <3 a properly built honda.



luke, sorry to derail your thread a bit man.
did i read somewhere that you got 1600cc injectors now? did you get the bosch? white top or the older version blue tops?

gsr interga wrote:

should just get a honda!

i'd probably be happier stepping in a steaming pile of fresh dog shit

V6Chris wrote:

gsr interga wrote:

should just get a honda!

i'd probably be happier stepping in a steaming pile of fresh dog shit

gsr interga wrote:

V6Chris wrote:

gsr interga wrote:

should just get a honda!

i'd probably be happier stepping in a steaming pile of fresh dog shit

yes i'd probably let my load off on a honda

Drastic. wrote:

luke, sorry to derail your thread a bit man.
did i read somewhere that you got 1600cc injectors now? did you get the bosch? white top or the older version blue tops?

no prob bro...

i got the 1630cc's from rage tek, i believe they are modified stock injectors, plug and play and no resistor box needed..

luke7019 wrote:

Drastic. wrote:

luke, sorry to derail your thread a bit man.
did i read somewhere that you got 1600cc injectors now? did you get the bosch? white top or the older version blue tops?

no prob bro...

i got the 1630cc's from rage tek, i believe they are modified stock injectors, plug and play and no resistor box needed..

they work ok?

i seen in his forum section on the nats that he had 1630 high imp's but he said his injectors were bosch based and i knew bosch didnt make any high imp 1600+ injectors.

are they all black?
if so i know where he got em from...fiveomotorsports. high imp is nice...just afraid to purchase any modified injector.. i just bought some 1680cc bosch white tops last nite...hopefully they work well for me on e85. going for 650-700.

you running e85? going bigger than a 30r?

Drastic. wrote:

luke7019 wrote:

Drastic. wrote:

luke, sorry to derail your thread a bit man.
did i read somewhere that you got 1600cc injectors now? did you get the bosch? white top or the older version blue tops?

no prob bro...

i got the 1630cc's from rage tek, i believe they are modified stock injectors, plug and play and no resistor box needed..

they work ok?

i seen in his forum section on the nats that he had 1630 high imp's but he said his injectors were bosch based and i knew bosch didnt make any high imp 1600+ injectors.

are they all black?
if so i know where he got em from...fiveomotorsports. high imp is nice...just afraid to purchase any modified injector.. i just bought some 1680cc bosch white tops last nite...hopefully they work well for me on e85. going for 650-700.

you running e85? going bigger than a 30r?

they look exactly the same as stock injectors (black), with blue o-rings and everything..they work fine so far, drivability is not wow but then again nemo never got to tune my drivability so idk..

yea i ran e85 (intank bosch 044, -6an feed from pump to rail, -4an return) , not going bigger, im most likely getting rid of the car..nobody wants to do 60 rolls anymore

luke7019 wrote:

Drastic. wrote:

luke7019 wrote:

Drastic. wrote:

luke, sorry to derail your thread a bit man.
did i read somewhere that you got 1600cc injectors now? did you get the bosch? white top or the older version blue tops?

no prob bro...

i got the 1630cc's from rage tek, i believe they are modified stock injectors, plug and play and no resistor box needed..

they work ok?

i seen in his forum section on the nats that he had 1630 high imp's but he said his injectors were bosch based and i knew bosch didnt make any high imp 1600+ injectors.

are they all black?
if so i know where he got em from...fiveomotorsports. high imp is nice...just afraid to purchase any modified injector.. i just bought some 1680cc bosch white tops last nite...hopefully they work well for me on e85. going for 650-700.

you running e85? going bigger than a 30r?

they look exactly the same as stock injectors (black), with blue o-rings and everything..they work fine so far, drivability is not wow but then again nemo never got to tune my drivability so idk..

yea i ran e85 (intank bosch 044, -6an feed from pump to rail, -4an return) , not going bigger, im most likely getting rid of the car..nobody wants to do 60 rolls anymore

whatttt. dont get rid of your car man. what u need is a bigger turbo, fully built motor, head, and input shaft. then u wont have to worry about anything breaking.

do 40rolls bro.
get 26" slicks. dont drive all over town on em. just slap em on at the spot and handle your business. buy a n2mb BOOST box.

i can hook a 40 roll on low boost in 2nd, and rape out on 3rd w/ full boost. our gear ratios are very potent..combine that w/ the torquey 2.4 and a longer rev limit w/ a turbo making power to 7-7500, and you will have a car hard to beat (if it hooks).

did your injectors come w/ a deadtime/latency sheet?

Drastic. wrote:

luke7019 wrote:

Drastic. wrote:

luke7019 wrote:

Drastic. wrote:

luke, sorry to derail your thread a bit man.
did i read somewhere that you got 1600cc injectors now? did you get the bosch? white top or the older version blue tops?

no prob bro...

i got the 1630cc's from rage tek, i believe they are modified stock injectors, plug and play and no resistor box needed..

they work ok?

i seen in his forum section on the nats that he had 1630 high imp's but he said his injectors were bosch based and i knew bosch didnt make any high imp 1600+ injectors.

are they all black?
if so i know where he got em from...fiveomotorsports. high imp is nice...just afraid to purchase any modified injector.. i just bought some 1680cc bosch white tops last nite...hopefully they work well for me on e85. going for 650-700.

you running e85? going bigger than a 30r?

they look exactly the same as stock injectors (black), with blue o-rings and everything..they work fine so far, drivability is not wow but then again nemo never got to tune my drivability so idk..

yea i ran e85 (intank bosch 044, -6an feed from pump to rail, -4an return) , not going bigger, im most likely getting rid of the car..nobody wants to do 60 rolls anymore

whatttt. dont get rid of your car man. what u need is a bigger turbo, fully built motor, head, and input shaft. then u wont have to worry about anything breaking.

do 40rolls bro.
get 26" slicks. dont drive all over town on em. just slap em on at the spot and handle your business. buy a n2mb BOOST box.

i can hook a 40 roll on low boost in 2nd, and rape out on 3rd w/ full boost. our gear ratios are very potent..combine that w/ the torquey 2.4 and a longer rev limit w/ a turbo making power to 7-7500, and you will have a car hard to beat (if it hooks).

did your injectors come w/ a deadtime/latency sheet?

no they didnt come with deadtimes, i ordered them at rage in person, put them in and nemo tuned the aem..

wow nice runs luke! when are we gonna run it?

Bring out the silver turtle hector, i'll drive it lol

SRTMIAMI wrote:

wow nice runs luke! when are we gonna run it?

car blew

wow luke thats fucked up! well if anyone knows the kid in the evo... ill run him..

SRTMIAMI wrote:

wow luke thats fucked up! well if anyone knows the kid in the evo... ill run him..

you'd have to sign up at [You must be registered and logged in to see this link.] and call him out there, i dont think he is on this forum...his name on that forum is "firstnameFERlastnameREA"...btw that evo is faster than you think, you should first run raul aka "rgsrt4" on here, he's also on myfloridasrt.com on top of the big turbo srt KOTS list btw..